You open the washer expecting damp clothes and find a tub full of gray water instead. The cycle says it finished, the clothes are sitting in it, and the water is not going anywhere. A washing machine not draining is one of the most common washer complaints, and it is also one of the most misread — because standing water can mean two different things.
The first question is whether the drum ever spun. If the machine hummed, clicked, or sat silent and the clothes came out soaking with the tub still full, the spin cycle never happened. That is covered in our companion guide, Water Stuck in Washing Machine? Won’t-Spin Checks to Try First, where the lid, the load, and the drive parts that make the drum spin are the problem. This guide covers the other half: the drain side. If the drum spun at full speed and the water still stayed behind, the pump, the hose, or the filter is not letting the water out — and that is what the checks below work through, in order, from the free ones first.
How Your Washer Actually Drains
A washing machine does not just let water run out. Draining is a short sequence, and every step has to pass before the next one starts.
First the machine finishes the wash and opens the drain path. Then the drain pump runs, pushing water out through the drain hose and into the standpipe or laundry sink. On a front-load machine, the water passes through a small drain filter first, which catches coins, hair, and lint before they can reach the pump. On a top-load machine, the same job is done by a filter or trap inside the tub or behind a lower panel, depending on the model.
That order is why the checks below start with the filter and the hose — the two places where a blockage is most likely and cheapest to fix — before the pump and the household drain, which are technician or plumber jobs. A washing machine not draining after a normal spin almost always comes down to one of these four places: a clogged filter, a kinked or blocked hose, a failed pump, or a blocked standpipe.
Common Causes at a Glance
| Cause | What you may notice | First safe check |
| Clogged drain filter | Water drains slowly, then stops; small items in the filter | Clean the filter at the front bottom panel |
| Kinked or blocked drain hose | Water backs up, hose feels full or bent | Straighten the hose, check for kinks |
| Drain pump failure | Humming but no water leaves, or silence when it should pump | Listen for the pump, check the impeller |
| Standpipe or household drain blocked | Water rises in the standpipe, other drains slow too | Check whether other drains are slow |
| Drain hose too low or too high | Water siphons back, or the pump cannot lift it | Check the hose height against the manual |
| Control or drain-cycle fault | Machine skips the drain step, same error code returns | Note the code, try one reset |
| Over-sudsing | Excess foam, drain seems slow, error code | Use less detergent, run a rinse |
| Frozen drain hose (cold laundry rooms) | No water leaves in cold weather | Warm the room, check the hose for ice |
This table is a starting point, not a diagnosis. The checks below follow the same order.
Safety First: Before You Touch Anything
A washing machine mixes water and mains electricity, and a full tub holds several gallons. Use this short checklist before any check below:
- Unplug the machine before touching the pump, the filter housing, or any wiring. Do not work on live parts.
- Never reach into the drum while it is spinning or trying to spin. Wait until it has fully stopped.
- Do not tip the machine while the tub is full. Bail or drain the water first, or it will flood the floor and reach the motor and wiring underneath.
- Mop up standing water before you move the machine. A wet floor and a heavy appliance are a bad combination.
- Keep towels and a shallow tray ready before you open the drain filter — the water behind it will come out fast.
- If you smell burning, see sparking, or find damaged wiring, stop, unplug the unit, and call a professional.
Check 1: The Drain Filter — the Most Common Cause
Start here: a clogged drain filter is the most common reason a washer stops draining, and it costs nothing to fix. Coins, hair ties, buttons, and lint collect in the filter over months, and one small item is enough to slow the pump to a stop.
On most front-load machines, the filter sits behind a small access panel at the front bottom of the machine. On many top-load machines, it is inside the tub rim or behind a lower rear panel — check your manual for the exact spot, because it varies by brand. Before you open it, bail out as much water as you can with a jug, then put towels and a shallow tray under the panel. The water behind the filter will come out as soon as you unscrew it, so turn it slowly and let it drain into the tray.
Pull the filter out and rinse it under running water. Pick out hair, lint, and anything solid, and look inside the housing with a flashlight for anything the filter missed — a coin sitting behind the filter can block the pump even after the filter itself is clean. Push the filter back in firmly and close the panel, then run a drain-and-spin cycle with the drum empty. If the water leaves normally, the filter was the problem. Clean it every month or two from now on, and check pockets before every wash: coins and hair ties are the most common things found in a blocked filter.

Check 2: The Drain Hose — Kinks, Height, and Blockages
If the filter is clean and the water still stays, look at the drain hose. It runs from the back of the machine to the standpipe or laundry sink, and it is easy to kink when the machine is pushed back against the wall.
Pull the machine out just enough to see the hose — do not tip it while the tub is full. The hose should run in a smooth curve with no sharp bends, no crushing where it passes behind the machine, and no sagging loop sitting on the floor. A kinked hose feels firm and full at the bend; straighten it gently and run a drain cycle. If the hose is cracked, split, or flattened where it was crushed, replace it rather than taping it — a drain hose replacement is a cheap part, and a taped hose will leak sooner or later.
Height matters too. Most manuals ask for the end of the drain hose to sit roughly 30 to 40 inches above the floor, held in the standpipe by its hook. If the hose end sits too low, water can siphon back into the tub after the pump stops. If it sits too high, the pump cannot lift the water far enough and the drain stalls. Check the height against your manual, not against a guess, because the right height varies by model.
Finally, check the end of the hose itself. Lint and detergent residue can build up inside the last few inches, and in a cold laundry room the hose can even freeze in winter. Run water through the hose into a bucket if you can disconnect it safely — if it flows freely, the hose is not the problem.

Check 3: The Drain Pump — Listen Before You Touch
The drain pump is the part that pushes water out, and it tells you a lot if you listen to it. Start a drain-and-spin cycle and stand near the machine during the drain step.
If you hear a steady hum and the water level does not fall, the pump is running but blocked — something is jamming the impeller, the small fan inside the pump that moves the water. If you hear nothing at all during the drain step, the pump may not be getting power, or it may have failed. If you hear a grinding or rattling noise, stop the cycle: a hard object such as a coin or a bra wire has reached the pump, and running it further can break the impeller.
Reaching the pump means removing a panel and working near wiring, so on most machines it is a technician job. One check you can do safely is the filter check above — a surprising number of “dead pump” calls turn out to be a coin sitting just behind the filter. If the filter is clean, the hose is clear, and the pump still hums without moving water, or stays silent, call a technician with the model number and the sound you heard. A drain pump replacement often costs roughly $200 to $300 installed.

Check 4: The Standpipe and the Household Drain
Sometimes the machine is fine and the drain it empties into is the problem. This is easy to miss, because the washer is the loudest thing in the laundry room.
Watch the standpipe — the open pipe the drain hose sits in — while the machine drains. If water rises up the standpipe and spills over, or gurgles back, the blockage is in the household drain, not in the washer. Check whether other drains in the house are slow too: a slow bathroom sink or a gurgling toilet at the same time points to a shared drain problem, and that is a plumber’s job, not a washer repair.
Do not pour drain cleaner down the standpipe to fix it. Caustic cleaners can damage the washer’s hose and pump seals if they back up into the machine, and they rarely clear a real blockage. A plumber can snake the line properly, and if the problem returns often, ask about a vent problem — a blocked vent pipe on the roof can make drains run slow throughout the house.
Check 5: Over-Sudsing and the Wrong Detergent
Too much detergent can look exactly like a drain failure. Excess foam fills the tub, slows the pump, and on many machines triggers an error code that stops the drain step altogether. High-efficiency (HE) machines are the worst for this, because they use very little water and need very little detergent.
If you see a tub full of foam, stop the cycle and let the foam settle. Scoop out what you can, then run a rinse-and-spin cycle with no detergent at all. Use only HE detergent in an HE machine, and use less than the bottle suggests — a tablespoon or two is often enough for a normal load. If over-sudsing happens on every wash, the detergent dose is the problem, not the pump.
Check 6: Error Codes and a Simple Reset
Modern washers display error codes for a reason, and the code is the fastest way to separate a drain problem from a spin problem from a control problem. Write down the exact code and look it up in the manual, or on the manufacturer’s support site for your exact model number — on a sticker inside the door or on the back. Do not guess from a code for a different brand: the same code can mean different things on different machines.
One reset is worth trying for a control glitch. Unplug the machine for a full minute, plug it back in, and run a short drain-and-spin cycle with the drum empty. If it drains normally, the control board likely glitched and the machine is fine. If the same code returns, or the machine stops at the same point again, do not keep resetting it. A control board replacement often costs roughly $300 to $500 installed, and on an older machine that cost is the point where pricing a replacement starts to make sense.
What Repairs Cost, and When Replacement Makes More Sense
Treat every figure as an approximate US planning range, not a quote, and get a written estimate before authorising work.
| Repair | Approximate planning range (installed) |
| Drain filter cleaning (DIY) | $0 |
| Drain hose replacement | $100 to $200 |
| Drain pump | $200 to $300 |
| Control board | $300 to $500 |
| Plumber — standpipe / household drain | $150 to $400 |
Age matters as much as price. On a washer under eight years old, a pump or a hose is usually worth fixing. On a machine over ten years old, or when two expensive parts fail at once, the repair can cost half the price of a new machine. If a technician quotes more than half the cost of a comparable new washer, ask for the numbers in writing before deciding.
Preventing Drain Problems in the Future
Most drain failures are preventable with three habits. Clean the drain filter every month or two, and check pockets before every wash: coins, hair ties, and small items are the most common things found in a blocked filter. Use the right amount of HE detergent — less than you think — and run a hot cleaning cycle once a month to clear detergent residue from the pump and hoses. Leave the lid or door open between washes so the drum dries out, and check the drain hose once a year for kinks, cracks, or sagging where the machine has been pushed back against the wall.
Your Quick Plan
If the tub is full of water and the washer will not drain, work through this order and stop as soon as it drains:
- Bail out enough water to reach the clothes, then check whether the drum spun — if it never spun, see the companion spin guide first.
- Clean the drain filter at the front bottom panel, with towels and a tray ready.
- Straighten the drain hose, check its height, and look for kinks or cracks.
- Listen for the pump during a drain cycle — humming without draining means a blockage; silence means a failed pump.
- Watch the standpipe while it drains — water rising there means a household drain problem, not a washer problem.
- Note any error code, try one unplug-and-reset, and retry once.
If the water leaves after any step, run one full cycle with a small load to confirm the fix. If it still will not drain, call a technician with the error code, the sound the pump made, and the checks you already tried.
Frequently Asked Questions
Why is my washing machine not draining?
A washing machine not draining most often means the drain filter is clogged, the drain hose is kinked, or the drain pump has failed. Clean the filter first — it is free and it is the most common cause — then check the hose, then listen for the pump. If the drum never spun, the problem is on the spin side instead.
Can I drain the water manually?
Yes. Bail most of it out with a jug, then use the drain hose or the filter access panel at the front bottom of the machine to release the rest into a shallow tray. Keep towels ready, and do not tip the machine while the tub is full.
Why does my washer drain slowly but not completely?
Slow draining usually means a partial blockage — lint and detergent residue in the filter or hose, or a pump impeller that is starting to jam. Clean the filter and check the hose first. If it drains slowly on every cycle, the pump is wearing out and should be checked before it fails completely.
How do I know if the drain pump is broken?
Start a drain cycle and listen. A steady hum with no water leaving usually means the pump is blocked. Silence during the drain step usually means the pump has failed or is not getting power. Grinding or rattling means a hard object has reached the pump — stop the cycle and call a technician.
Is it safe to use drain cleaner in a washing machine?
No. Do not pour drain cleaner into the washer or down the standpipe. Caustic cleaners can damage the hose and pump seals if they back up into the machine, and they rarely clear a real blockage. Clean the filter and hose by hand, and call a plumber for a blocked household drain.
When should I call a professional instead of checking myself?
Call a professional if the pump hums but moves no water, the pump stays silent, the same error code returns after a reset, or water rises in the standpipe. Call sooner for burning smells, sparking, or damaged wiring — and unplug the machine in the meantime.
Related Guides
- MyHomeMag homepage
- Appliance Guides category
- Washing Machine Leaking: Find the Source, Stop the Water, and Fix It Safely
- Dishwasher Not Draining? Causes, Fixes, and When to Call a Pro
- Fridge Not Cooling but Freezer Works? Causes and Safe Checks
- Water Stuck in Washing Machine? Won’t-Spin Checks to Try First
- Dryer Not Heating? Electric and Gas Checks to Try First
- Dryer Takes Too Long to Dry? Vent and Airflow Fixes to Try
- Washing Machine Shaking Violently? Level It and Stop the Banging

9 Responses